Plumbing 101: Tips for Installing a Bathtub
Plumbing 101: Tips for Installing a Bathtub
Blog Article
On this page down the page yow will discover lots of worthwhile news all about Tools You Need to Install a New Bathtub .
Mounting a tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a new one is also a reasonably difficult job. If the old tub is readily obtainable, the project can move speedily; if you need to open up a wall surface to remove the old bathtub and also place the new tub, the job is much harder. In either situation, the project is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the new one. See to it you have actually qualified yourself for the task as well as fit trying it. As opposed to working with a professional to take control of a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually currently purchased a brand-new bathtub as well as don't require to alter the setup of your previous water system pipes.
Your tools and product checklist should comprise the following:
Planning for the Setup
To start with, the supporting structure supplied with the bath needs to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to avoid pressure on the tub.
Fit the adaptable tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be rather troublesome as a result of the limited accessibility that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new faucets, contrast the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Using the two wood boards under its feet, position the tub in the required position. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the bathtub up until the spirit level reads level.
To install faucets, fit all-time low of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water system as well as examine all joints and new pipework for leaks as well as tighten them if required. Load the bathtub and also check the overflow outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's instruction manual. Tiling as well as sealing around the tub ought to wait until the bath tub has actually been made use of at the very least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in area between the tap and the sink. Protect the faucet in position with the maker offered backnut. As soon as the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack an inflexible seal, triggering the water to permeate the wall between the bathroom as well as the tiling, causing problems with dampness and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, as well as are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to always load the bathtub with water prior to sealing, to enable the activity experienced when the bathtub remains in use. The sealant can break relatively early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently offered on the market. It is recommended to fit the ceramic tiles making use of water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on How to Install a Bathtub Yourself, I imagined sharing that blog post was essential. Are you aware of somebody who is excited about the topic? Take a moment to promote it. Thanks so much for your time spent reading it.
Drainage issues? Inform. Report this page